How to Do a Proper Deadlift step by step

How to Do a Proper Deadlift step by step
Photo: Wikimedia Commons

Learning how to do a proper deadlift will build raw power in your glutes, hamstrings, and whole back faster than almost any other exercise. It is the king of lifts, but many people walk away from the barbell because their lower back aches the next morning. You do not need to hurt to get strong.

To lift safely, set your feet hip-width apart under the bar, bend at your hips to grip the steel, drop your hips until your shins touch the bar, flatten your back, and pull up by pushing your feet into the floor. That simple set of steps keeps the heavy weight close to your legs and protects your spine every single time.

Set Up Your Feet and Grip the Bar

Every bad lift starts with a bad setup. Stand with your feet hip-width apart, which is narrower than your squat stance. Your toes should point straight ahead or out just a tiny bit. Look down at your feet. The loaded barbell should sit directly over the middle of your foot, about one inch away from your shins.

Without moving the bar or dropping your hips yet, push your butt back and bend at your waist. Reach straight down and grab the bar just outside your legs. You can use a double overhand grip, where both palms face you. This grip keeps your shoulders even and builds great grip strength in your forearms.

My gym partner Mark used to stand three inches back from the bar because he was afraid of scraping his shins. He ended up pulling the weight in a big arc, which made 135 pounds feel like 300 pounds and strained his lower back. Once he stepped closer, the weight flew off the floor.

Keep your arms completely straight. Think of your arms like steel cables and your hands like iron hooks. You are not going to bend your elbows to pull the weight up. All the work will come from your legs and hips.

How to Do a Proper Deadlift step by step
Photo: Wikimedia Commons

Set Your Back and Pull the Slack Out

Now that your hands are on the bar, bend your knees slightly until your shins touch the metal. Do not let the bar roll forward when your shins make contact. It must stay over the middle of your foot. If the bar rolls, start your setup over from the beginning.

Next, raise your chest up proud. This action naturally flattens your lower back and puts your spine in a safe position. Pull your shoulders down and back, like you are trying to squeeze an orange in your armpits. This simple cue turns on your lats and protects your upper back from rounding under heavy loads.

Before the weight leaves the ground, you need to pull the slack out of the bar. Put upward pressure on the bar until you hear a small click from the metal plates hitting the bar sleeve. You should feel tension in your hamstrings and back before the plates even lift off the rubber mats. Building this tension prevents your hips from shooting up too fast.

If you want to build a solid upper body to match your lift, try combining this pull day work with a Back workout for a stronger posture and less pain to keep your shoulders balanced.

Stand Up by Pushing the Floor Away

Take a big breath into your stomach, hold it tight, and press your feet flat into the ground. Do not think about pulling the bar up with your arms or upper body. Think about leg pressing the floor away from you. This mental trick keeps your hips and shoulders rising at the exact same speed.

The bar must drag right along your shins and stay close to your thighs as it moves up. If the bar drifts away from your skin even one inch, it creates a long lever that puts extra pressure on your lower spine. Dragging it up your legs feels strange at first, but it is the safest way to move heavy weight.

Keep your head in a neutral position. Look at a spot on the floor about six feet in front of you instead of staring straight up into the gym mirror. Straining your neck upward puts unnecessary stress on your neck muscles and upper spine while you lift heavy loads.

Finish the movement by standing up tall and squeezing your glutes hard at the top. Do not lean backward at the top of the lift. Hyper-extending your lower back at the finish line does not add any muscle benefit and sets you up for painful spine pinch injuries later on.

Lower the Weight with Control

Getting the bar back down to the ground is just as important as lifting it up. Many lifters relax at the top and drop the weight with a rounded spine. This mistake is where a lot of gym injuries happen. You must stay locked in until the bar rests still on the floor.

To start the descent, push your hips back first while keeping your knees slightly bent. Let the bar slide straight down your thighs. Only after the bar passes your knees should you bend your legs fully to drop the plates back to the mat. This two-part drop keeps the bar path straight up and down.

Do not let the bar bounce off the floor to make the next rep easier. Let the weight settle completely on the floor for one full second. This is called a dead stop, which is where the exercise gets its name. Re-set your breath, check your back, and lift again from a dead stop.

Controlling heavy lifts is a core part of strength training because it forces your muscles to work through both the lifting and lowering parts of the move.

How Many Sets and Reps Should You Do?

Because this exercise uses almost every muscle in your body, it taxes your nerves and muscle fibers quickly. You do not need endless sets to get strong. Quality reps always beat high numbers when you are working with heavy iron.

If you want to gain pure strength, pick a weight where you can do 3 sets of 5 reps. Rest for a full 3 minutes between sets so your energy recovers completely. If your main goal is building muscle size, aim for 4 sets of 8 reps with 2 minutes of rest between sets. Beginners should start with 3 sets of 8 light reps to build great habit patterns.

  • Beginner Form Practice: 3 sets of 8 reps with 90 seconds rest.
  • Muscle Growth: 4 sets of 6 to 8 reps with 2 minutes rest.
  • Pure Strength: 3 sets of 5 reps with 3 minutes rest.

You can learn more about how to structure your whole week by checking out our gym workout guides for beginners to make sure you rest enough between hard sessions.

Fix These Common Safety Mistakes

The most common error in the gym is rounding the lower back. This happens when you try to lift a weight that is too heavy, or when your legs are too far from the bar. When your spine rounds under a heavy load, the pressure shifts from your big muscles directly onto your soft spinal discs. If your back rounds, stop the set right away and drop the weight down.

Another big mistake is letting your hips shoot up before the bar leaves the ground. If your butt jumps into the air first, your legs stop helping with the pull. Your lift turns into a stiff-legged pull using only your lower back. Focus on pushing through your heels so your chest and hips rise together.

Lastly, do not wear thick running shoes with soft gel soles when you lift heavy bars. Soft shoes act like mattresses under your feet, making you wobble and shift weight to your toes. Wear flat shoes with hard soles like Chuck Taylors, or lift in your socks if your gym allows it. A firm connection to the ground builds a strong base.

Staying safe while lifting heavy is key to building good physical fitness over many years without taking long breaks for injuries to heal.

Set your feet close to the bar on your very next workout, keep your chest high, and focus on pushing the floor away. How does your lower back feel during your current lifting sessions?

Comments

Popular posts from this blog

30 Minute Full Body Gym Workout for Busy People

Back workout for a stronger posture and less pain

Leg day for beginners without injury